Install Carpet without Knee Kicker ( 5 Critical Points )

Do you know that you can Install Carpet without Knee Kicker ? Most of the time, customers come across the phrase ‘knee kicker’ while installing their newly bought carpet by themselves. You must have seen the word in the instruction manual while setting your carpet. If you are wondering what the phrase means, continue reading this article.

You can install your carpet without a knee kicker. It is an interesting tool that will help you set your carpet. You can also create your knee kicker if you follow this article.

What is a Knee Kicker?

Install Carpet without Knee Kicker

It is a tool that helps you stretch your carpet while installing it and for later usage. Intezar is also known as a carpet stretcher. There is another type of carpet stretcher known as a power stretcher.

A knee kicker is installed when you have to kick the back of it with your knee, creating tension on the carpet.  Kicking the back will fit the carpet nicely with the wall. A knee kicker is generally used for smaller rooms within ten square feet in area.

Knee kickers are not very expensive, which you can buy for less than thirty dollars. However, finding a knee kicker in your local market can be difficult. Then you have to install the new carpet without a knee kicker. Do not worry as much as possible.

How to Install Carpet without Knee Kicker

The following five steps will help you lay a carpet without any knee kicker.

  • Fixing tack strips
  • Cut and lay a carpet pad
  • Cut and lay the carpet
  • Stretch the carpet
  • Connect the carpet to the strips
  • As simple as that!

Installing a carpet without a knee kicker can be tricky and involve hard work. A knee kicker helps buckle the carpet and also helps with the creases. You can easily lay your carpet crease-free while using a knee kicker. There is a way to lay your carpet crease-free without using a knee kicker. To achieve the crease-free look, you have to prepare yourself by wearing anti-slip rubber bottom shoes.

Here are some of the steps to install a new carpet without the help of a knee kicker.

Installing the Tack Strips

First, you have to check if the subfloor is appropriate for installing a carpet. After that, you have to install the trips along the perimeter of the room. It is suggested to place the tack strips along with the half-inch between the walls. The process does not involve stretching the carpet; you will have to directly please the tack strips along the wall of the room.

Cutting and Installing Carpet Padding

Cutting and Installing Carpet Padding

Next, you have to measure the carpet pads in order to match the dimension of the room perimeter. You can use a knife to cut the carpet pad. You can cut it into square pieces, but you have to leave the thickness of the tack strips.

After cutting the corporate pad into small squares, you can start laying from the corner of the room. It is better to start laying them near the door. You must not place the carpet on the tack strip, but it should be placed closest to them. You apply glue or adhesives to fix the carpet edges. You can also fix the edges with staples.

Cutting and Laying Carpeting

You have to use a carpet cutter to size them according to the perimeter of the floor. You can also skip this step if you have ordered it in square form. Begin from the corner of the room to install them. Slowly begin to unroll the carpet as you move towards the door.

Stretching the Carpet

In order to stretch the carpet, you have to use the jump method. After laying the pieces on the carpet, you have to return to the tack strip. You have to jump forward facing the wall towards the tack strip along with a distance of about one foot. In this way, you are creating momentum that is causing the carpet to stretch properly. The carpet will gradually meet the tack strips. You might have to repeat this process several times in order to fulfill the desired positioning.

Connecting the Carpet to the Tack Strips

Connecting the Carpet to the Tack Strips

You have to wear gloves to place the edges of the carpet on the tack strips. You have to fix the edges carefully. You have to do the same to all the edges of the carpet along the perimeter of the room until all the edges are fixed.

You can walk around and inspect each edge of the carpet carefully. You want to do this to make sure the carpet is shaped properly to the lengths of the wall and not rising above or touching the wall. If required, you can trim the extra parts with a carpet cutter.

The installation is finished. This time without any help of a knee kicker.

How to Check that the Carpet is Installed Properly

It can be tricky for a beginner to become satisfied after the installation of a new carpet. You might doubt yourself.

But there is a way to understand if the process is completed. You check the following points to be sure.

Firstly, check for wrinkles and folds on the surface of the carpet. Look for any distorted ripple on the carpet. Creases that become prominent near the edges show that the installation has faults. If there are creases, then the carpet was not pulled enough over the tack strips.

Sometimes pressing on the wrinkles with your foot can remove them. It is not going to vanish all the time. Then you have to understand that the fitting was not done perfectly. You might have to redo it.

You can also check the leveling of the carpet. You can lie down on the floor to check the level of the carpet. If you see any dip or buckle on the surface, then the carpet is not set right. If the crease does not recede, you might have to redo the installation. The leveling can also be disrupted due to the uneven subfloor.

How to Create Your Knee Kicker

Knee kickers are not much expensive and are budget-friendly. They are around thirty dollars in the retailer. You can also make a knee kicker for yourself. It is possible that you cannot find a knee kicker in your local market. Then you must carefully read the following guideline.

The items required to make a knee kicker;

  • Tool to cut tack strips
  • Pieces of Tack strips
  • Electric saw
  • A plack or ply of 4by 4 size
  • Sandpaper
  • Adhesive of wood
  • Foam piece of 5 by 5-inch size
  • A piece of upholstery fabric of 8by 8 sizes.

Here’s how to do this simple project.

First, you have to cut the plank using an electric saw. You want to size it into 16 inches. Then use sandpaper to smooth the wooden surface. The surface of the plank should be completely smooth. You have to do this step to avoid getting splinters while using the knee kicker.

The second step involves cutting the tack strips into four inches strips. You can use the tack strip cutter to do this step. You can also use the saw to fulfill this step if you do not possess a tack strip cutter. You must have five to six strips for the front part of the kicker. You have to wear gloves while tackling the tack stripes as they can injure your hands and fingers.

Thirdly, you have to attach these strips to the plank. You can use any glue or adhesives to attach the strips to the wood plank. Apply the glue at each end of the wood and place the pieces with the back first on top of the front part. After that, you have to place the patch pieces with the teeth facing towards you. Now you have to wait till the glue dries.

Then you attach the kicker pieces one by one. You have to stick the bottom of the wood plank with glue that will play the kicker. Then you have to use the upholstery fabric piece as a thick pad to support it on top with glue. You have to glue the fabric on top of the foam. You above to secure the foam edges. You have to be sure that the foam or the fabric does not fall off while using. You have to let the glue dry.

At last, you have to test the knee kicker. You have to be sure if all the pieces are in place. If the pieces are not in place, then there must be a possibility for the user to get harmed while using. First, you will want to practice before utilizing the DIY knee kicker a few times. If the padding is safe and the upholstery fabric is placed right, the tool is ready to use.

Conclusion

This proves that the carpet can be installed without any knee kicker. The installation can become tricky without a knee kicker, but it is still possible to set your carpet perfectly if you properly follow the guidelines mentioned above.

Leave a Comment